• The safety software circuits has been realized by the redundancy logic circuits.
• Short E-Stop reaction time by hi-speed processing time and space saving has been realized
• More reliable safety circuit program is available by fault detection function and shorten design lead time.
• Down-sizing of safety control circuit is realized by FB function(Function Block)
• Field wiring reduction by Safety-networking and safety signal communication
• MTTR improvement by employment of control visualization technology

• Global oriented I/O module, communication functions and large scale CPU are unified PLC as a TOYOPUC-PC3JG-P.

• PA library function, PC / CMP-LINK:2 port standard, and 7 segment display machine are added for the function/form of PC3J-CPU as it is. Furthermore, it contributes to lead time shortening of the work from circuitry to preservation.

• TOYOPUC-PC3JD is an integrated system integrating CPU, communication, and I/O functions.
• Outside dimensions are identical with PC3J/PC2J also the CPU is mounted at slot 0 of PC3J/PC2J.
• Mountable on dedicated PC3JD base.
• Function of CPU is identical with PC3J-CPU. Communication abilities include device net with an additional 64 I/O equipped as standard.
• PC3JD 2.00 or later version is compatible with SFC program.

• It is the programmable controller which bears sequence control of an integrated control system.

• In MX-CPU, the thing to replace TOYOPUC-M and PC1 is a possible CPU module. MX-CPU can be installed on CPU-slot and slot 0 of the BASE module of PC3J/PC2J. Moreover, the MX-BASE can be connected with the PC1 bus (PG-I/O bus), and the I/O card for PC3J can be stored. To use MX-CPU and MX-BASE,TOYOPUC-M and PC1 can be replaced without change in the sequence program of M and PC1 and change in name of I/O LINE.

• J-DLNK-M2 is a TOYOPUC-PC 2J/3J DeviceNet compatible master module.

• The DRMT series is DeviceNet compatible Remote I/O terminal with input /output wiring short circuit or wire-cutting detection

• The F-DLNK-M is the master module for the TOYOPUC-PCF/FS.
• The J-DLNK-M is the master module for the TOYOPUC-PC3J/2J.

• It is a master module in accordance with AS-i(Actuator Sensor Interface).
• The data of 124 points of input/124 points of output can be exchanged with the 31 slaves or less.
• The network wiring length is 100m or less.
• The cycle time of AS-i is 5ms or less.
• The slave connection is one-touch because of a special cable.
• Connected form of network is free.

* AS-i is a cereal ministry wiring system which integrated the signal line with the power supply line.

• The S-LINK module contributes to the conserve wiring for equipment with the product corresponding to S-LINK of SUNX.

• FL/ET-net-5 is a module with the function of “FL-net" and "Ethernet".
  The FL-net mode and the Ethernet mode are switched with the dip switch in front of the module.
  FL-net is the best for the data link between a high-speed,/large capacity control equipment.
  Ethernet is the best for the communication by the command response with the personal computer.
  Please select left contents about details.
  Ethernet　is a registered trademark of Xerox.

• PCwin is the graphic language which was prescribed by international standard IEC61131-3 It is the programming tool for TOYOPUC which made a programming by SFC possible.

• Hellowin is a Windows® 95/98 based program used to interface with TOYOPUC [PC3J] and [PC2/PC2J] units.

• It is a cable for connecting a personal computer with PC3J / PC2J.

• This is a cable for connecting the USB terminal and TOYOPUC of a personal computer.